Install questions

ive been searching around to find someone who can install my alarm/starter but because its not therer product no one can do it and i had a few people tell me that they would gige it a try for 450-500 buks now i think i could do it but the diagram dosent tell me what wires go where can anyone help me out this is a page guard 8500s 2way system and a 2003 sunfire

 

i went there ive got the diagrams now but im trying to find out where the rest of my wires go from the alarm and also im trying to figgur out how to hook up the bypass module this is how far i am now
12 VOLT CONSTANT RED (+) IGNITON SWITCH HARNESS =
(pin 1) on 6 pin starter harness

STARTER YELLOW (+) IGNITION SWITCH HARNESS =
(pin 2) on 6 pin starter harness

STARTER 2 N/A

IGNITION 1 PINK (+) IGNITION SWITCH HARNESS =
(pin 3) on 6 pin starter harness green

IGNITION 2 N/A
IGNITION 3 N/A

ACCESSORY/HEATER BLOWER 1 ORANGE (+) IGNITION SWITCH HARNESS = (pin 4) on 6 pin starter harness blue

ACCESSORY/HEATER BLOWER 2 N/A

KEYSENSE N/A

PARKING LIGHTS ( - ) N/A

PARKING LIGHTS ( + ) BROWN (+) IN DRIVERS KICK PANEL =

POWER LOCK LIGHT BLUE (TYPE C) See NOTE *1 IN EITHER KICK PANEL

POWER UNLOCK WHITE (TYPE C) See NOTE *1 IN EITHER KICK PANEL

LOCK MOTOR WIRE GRAY (+) IN DRIVERS DOOR HARNESS

DOOR TRIGGER See NOTE *2 IN DRIVERS KICK PANEL and PASSENGER KICK

PANEL 14301_SUNFIRE_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf


DOMELIGHT SUPERVISION GREEN/BLACK (-) IN DRIVERS KICK PANEL =
(pin 7)on 14 pin main harness grey wire

TRUNK RELEASE BLACK/WHITE (+) @ BCM, See NOTE *3

SLIDING POWER DOOR N/A

HORN BLACK (-) @ STEERING COLUMN HARNESS

TACH PURPLE/WHITE IN MAIN ENGINE HARNESS

WAIT TO START LIGHT N/A

BRAKE WHITE (+) @ SWITCH ABOVE BRAKE PEDAL =
(pin 8)on 14 pin main harness red & white wire

FACTORY ALARM DISARM N/A

ANTI-THEFT YELLOW (+) and BLACK (-) and WHITE (Not Used) GM's PASSLOCK 2 System, wires are under the Steering Column cover, at the Bottom of the Ignition Switch Tumbler in a BLACK or DARK GRAY Plug

thats what i got so far and this is what im missing

Pin 5 orange on 14pin main wire harness armed output (-)500mA. The qrange wire provides a ground output while armed to activate a relay for starter defeat and anti-grind protection.

pin 12 yellow: generator input (+) connect to the wire that shows more then (+)6v when engin is running this wire detects the status of the engine

pin 3 white left signal light
pin 4 white right signal light

and also i need to know what connects to the clutch switch

 

is anyone there to give me a hand

 

dose this look right ta any one out there who knows a little bit about installin a alarm

 

anyone here

 

ive got a better diagram if youd like to see it its everything i got hooked up and the things im missing but i dont know how to upload it id go to the 12volt website but they didnt want to help me this is my verry firs install and id like it to go smooth

 

ive already started to do it just because all the install shops i wen to dont want to go near it because its not there product they want to charge me 500buks to do it i dont have that kinda money this is what ive got so far

6 Pin Starter Harness

Pin 1: RED WIRE Main power input (+12 volt).
Connected Pin 1: 12 volt constant red (+) Ignition Harness

Pin 2: YELLOW WIRE Starter output (+12volt).
Connected to Yellow Starter (+) Ignition Harness

Pin 3: GREEN WIRE Ignition Output (+12volt).
Connected to Ignition 1 Pink (+) Ignition Harness.

Pin 4: BLUE WIRE Accessory Output (+12volt)
Connected to Accessory/Heater Blower 1 Orange (+ ) Ignition Harness.

Pin 5: BLACK WIRE Ground Input (-)
Connected just right of the steering column on the chassis.

Pin 6: WHITE WIRE Second Ignition Output (+12volt).
Did not connect this wire to anything.


14 Pin Main Harness

Pin 1: GRAY/BLACK: Option 1 Output (-500mA). Factory arm output
Din not connect this wire to anything. No Factor Alarm

Pin 2: Brown Siren Output (+) 3A.
Did not install siren

Pin 3: WHITE Left Signal Light Output (+) 10A.
Did not connect wire

Pin 4: WHITE Right Signal Light Output (+) 10A.
Did not connect wire

Pin 5: ORANGE Armed Output (-) 500mA.
Did not connect wire

Pin 6: PURPLE/BLACK Factory Disarm Output (-) 500mA.
Did not connect wire. No Factory Alarm

Pin 7: GRAY Dome Light Output (-) 500mA
Connected to dome light supervision GREEN/BLACK (-) in drivers kick panel.

Pin 8: RED/WHITE Brake Input (+).
Connected to Brake WHITE (+) @ switch above brake pedal
Pin 9: WHITE/BLACK Hood Pin Input (-).
Did not connect wire No hood pin as of yet.

Pin 10: GREEN Door Input (+ or -).
Did not connect wire.

Pin 11: PURPLE Ground When Running Output (-) 500mA.
Did not connect wire haven’t installed the bypass module.

Pin 12: YELLOW Generator Input (+).
Did not connect wire.

Pin 13: BLUE Trunk Input (-).
Did not connect wire

Pin 14: GREEN/BLACK Optional Trigger Input (-).
Did not connect wire.

 

whats exactly ive basically got everything hooked up but a few wires

 

got the alarm installed by an installer but he didnot do the power trunk and my camera dose not seem to work any sugestions also how would i make time starts on cold nights and auto arming this is what he never mentioned
PageGuard 8500s 2way Alarm

 

got everything working on this alarm but the trunk just looking for information on how to hook the trunk up to the alarm so it will work when trunk button is pressed thanks 03 sunfire with page guard 8500s alarm