4 Fi Audio IB3 18's walled off 15Hz tune in a VAN BUILD LOG

I paid extra to get the Ai-NET cable and the optical cable with the PXA-H701. The optical cable that i got has the same square head with the little knob, fiber optic, on both ends. Apparently I need an adapter to fit the back of the W505?

I was going to pull an all nighter to get the front stage completed... but I don't have the proper cable.

 

I paid extra to get the Ai-NET cable and the optical cable with the PXA-H701. The optical cable that i got has the same square head with the little knob, fiber optic, on both ends. Apparently I need an adapter to fit the back of the W505?

I was going to pull an all nighter to get the front stage completed... but I don't have the proper cable.

and NO GROMETS! I figure it's gonna blow up from duct tape and foam anyway so what the hell.

 

after I turned the deck on with the Ai-NET hooked up, it made the power to the factory speakers via the harness full blast after I clicked the volume from 0 to 1, so I disconnected the factory speakers and installed the front stage. It is in. I set the crossover settings to the PXA. No sound. If I turn it up, I get some sound, but inaudible.

anyway heres a vid of the build so far from earlier today as requested

http://www.youtube.com/watch?v=yw4eh5RPipc

 

seriousely...no help? I'm going out to take more pics and make another vid.. I got a lot done between yesterday at 10AM till this morning at 5AM...I'm up at 11AM again. No more posting here till I get some replies. I know there's a lot of lurkers here... No help? Please? I can't do anything right now...last night at 5AM I went to walmart and got another RCA last night and ran that from the deck to crossover...still no sound. When I turn the deck up I can kind of hear the song really distorted, so I know somehow it is getting from the deck to the speakers...got to be a setting.

Please?

 

ok i lied i gotta post... but i know u guys are watching, wont someone please hlp?

http://www.youtube.com/watch?v=Cn15z3nT9zs

 

well thank you for acnowlegin lol at least i know it's being thought about

 

OK last nite hooked up the crossover. After hooking it up, the factory speakers became full blast if volume wasn't set to 0. So going from 0 to 1 goes from nothing to full blast. Turning it louder did nothing. Disconnected them and installed speakers with amps.

No sound...well, very quiet and distorted once the volume is set to around 20... can hardly hear it, but it's there, and only thing u can make ou is the beat.

Had alpine dealer look at it today, the W505 does not have optical anymore! **** ME. So he looked at it, couldnt figure it out.

Then we hooked the RCAs strait from deck to 6.5's amp..850.4 they are LOUD. But, the volume does nothing! 0 there is nothing, turn it up to 1, and its full blast, turn up to 35 and back down, does nothing.

Hit the speaker icon button on the main display that usually gives me bass treble and subwoofer, now its MX something or other and its set to 3

 

thanks for lookin tho! FB sucks! lol

 

in that 1st vid i had the amps switched to off, now theyre on HP, so the FR125Ss are at 200Hz and the Extremis are at 50Hz. How do I have the crossover tested?

http://www.youtube.com/watch?v=QWupbMwyTr4

 

theres no dials, it is fully controlled from the deck

 

the HU went into a mode for the crossover. after I disconnected the Ai-NET and power then rehooked power, it went back

 

http://www.youtube.com/watch?v=AHrBzWJkNzs

http://www.youtube.com/watch?v=t5p4QjsgDJY