/ Register

Memphis Line Driver

Discussion in 'Car Audio Head Units' started by liftedranger08, Jan 12, 2009.

Page 1 of 2
  1. liftedranger08

    liftedranger08 Full Member

    The dude at the car audio shop told me to get a line driver for my system. I looked at the specs and the nine.1 amp can has an input of 7 volts and the radio only puts out 2 volts and the line driver lets the radio put out up to 9 volts. I found a memphis line driver for $69.99. Would this be worth getting?
     
    liftedranger08, Jan 12, 2009
    #1
  2. jonnyv713

    jonnyv713 The Young Gun of CAT

    jonnyv713, Jan 12, 2009
    #2
  3. G3n3R@1

    G3n3R@1 Full Member

    I would look into a PAC or soundgate.
     
    G3n3R@1, Jan 12, 2009
    #3
  4. jonnyv713

    jonnyv713 The Young Gun of CAT

    i was also thinkin pac but it didnt say the secs and output voltage
     
    jonnyv713, Jan 12, 2009
    #4
  5. jayz85

    jayz85 Full Member

    I vote for the epicenter that thing is dope but dangerous.
     
    jayz85, Jan 12, 2009
    #5
  6. jayz85

    jayz85 Full Member

    jayz85, Jan 12, 2009
    #6
  7. jonnyv713

    jonnyv713 The Young Gun of CAT

    ya, be very careful. Its so good, it can really damage some stuff.
     
    jonnyv713, Jan 12, 2009
    #7
  8. liftedranger08

    liftedranger08 Full Member

    Well i dont really wana spend $150 on it. So i guess the 2 channel that puts out 8 volts would be fine for me that is $49.99.
     
    liftedranger08, Jan 12, 2009
    #8
  9. jonnyv713

    jonnyv713 The Young Gun of CAT

    the $50 one is 6CH, the 2CH is $30
     
    jonnyv713, Jan 12, 2009
    #9
  10. liftedranger08

    liftedranger08 Full Member

    Do these work for highs/mids amps to? If so, do i need the 6 channel one for the sub and high/mid amp or will the 2 channel work?
     
    liftedranger08, Jan 12, 2009
    #10
  11. jonnyv713

    jonnyv713 The Young Gun of CAT

    if you are running the 4 CH and your sub amp you will need the 6CH one.
     
    jonnyv713, Jan 12, 2009
    #11
  12. liftedranger08

    liftedranger08 Full Member

    Ok i was just making sure. Thanks man. I will be getting it here soon along with 0 gauge wire, distribution blocks, and an extra battery. This should upgrade my electrical system somewhat.
     
    liftedranger08, Jan 12, 2009
    #12
  13. jonnyv713

    jonnyv713 The Young Gun of CAT

    what 0guage are you getting?
     
    jonnyv713, Jan 12, 2009
    #13
  14. liftedranger08

    liftedranger08 Full Member

    Prolly stinger wire since i can get it at my local shop and get a deal on it.
     
    liftedranger08, Jan 12, 2009
    #14
  15. jonnyv713

    jonnyv713 The Young Gun of CAT

    i got my KnuKonceptz KLMX for 1.75/foot i think
     
    jonnyv713, Jan 12, 2009
    #15
  16. liftedranger08

    liftedranger08 Full Member

    O ok, ill look around before i get it because i still have to measure how much i need. When i run 0 gauge to the dist. block, do i need to run 0 gauge to both amps to or will 4 gauge to the amps work?
     
    liftedranger08, Jan 12, 2009
    #16
  17. jonnyv713

    jonnyv713 The Young Gun of CAT

    i would think 4 would be suficient, but if you have enough just run 0 to the Nine.1
     
    jonnyv713, Jan 13, 2009
    #17
  18. pedro quiroga

    pedro quiroga Well-Known Member

    seen this a lil late. the PG unit will do a good job for all your amps. my old PG eq had a built in 8volt line driver and my PG amps were rated for 2v and they absolutely screamed and sounded soooo good doing it. id get that one for sure.

    damn i want to use those bad boys again. hmmmmmm
     
    pedro quiroga, Jan 13, 2009
    #18
  19. G3n3R@1

    G3n3R@1 Full Member

    4 gauge would be fine at a short length for both amps. But I would still try to get 0 gauge on the nine.1 just cause.
     
    G3n3R@1, Jan 13, 2009
    #19
  20. liftedranger08

    liftedranger08 Full Member

    Well, where my distribution blocks will be, there will b only about 6 inches of wire to each amp. Ill post pics when i get my wiring all done and cleaned up.
     
    liftedranger08, Jan 13, 2009
    #20
Page 1 of 2