/ Register

New system in my new car!

Discussion in 'General Car Audio Discussions' started by jonnyv713, Mar 23, 2008.

Page 4 of 8
  1. jonnyv713

    jonnyv713 The Young Gun of CAT

    from what i read so far it sounds like pretty good car except for the cupholder.
     
    jonnyv713, Apr 1, 2008
    #61
  2. cccullen

    cccullen Full Member

    it takes 5.25's in the front doors and 6x9's in the rear deck.
     
    cccullen, Apr 1, 2008
    #62
  3. jonnyv713

    jonnyv713 The Young Gun of CAT

    ugh... that 5 1/4 crap. maybe some kicks for this one too to house some 6 1/2's and then the kicker set up.
     
    jonnyv713, Apr 1, 2008
    #63
  4. jonnyv713

    jonnyv713 The Young Gun of CAT

    MTX Audio XT502 - Power Handling: Peak: 220 watts / RMS: 55 watts • High temperature aluminum voice coil with kapton former • Grilles included • Frequency Response: 60 Hz - 20,000 Hz - , Car Speakers, 5-1, 4" Speakers - Sonic Electronix
    maybe these in the doors for somethin cheap.

    Polk Audio db6501 6-1/2" 2-way Component System - 6-1/2" 2-way Component System (Marine Certified) • 300 watts Max • Aerated Polypropylene Cone • Neodymium Magnet Structure • Polyimide Voice Coil Former for high thermal stability • 1" Ring Radiator T
    these for the kicks

    Polk Audio db691 - 6" x 9" 2-way Speakers (Marine Certified) • Power Handling: Peak: 300 watts / RMS: 100 watts • Kapton voice coil former • ABS Grilles • Pole Plate Heat Sink • stamped steel basket • Frequency Response: 35-22,000 Hz - , Car Speakers
    these for the rear

    Kicker Solobaric L7 Car Stereo S15L7 Dual 4 Ohm 2000W Sub Subwoofer
    with
    Crunch GP2500D - Ground Pounder Series 1-Channel Class D Car Amplifier • 625W x 1 chan. @ 4 ohms • 1250W x 1 chan. @ 2 ohms • 2500W x 1 chan. Max • PWM MOSFET Power Supply • DC, short, thermal, and overload protection circuitry - , Car Amplifiers, Mo
     
    jonnyv713, Apr 1, 2008
    #64
  5. jonnyv713

    jonnyv713 The Young Gun of CAT

    o and did i tell u they only want $750 for the car? but idk what i am gonna do. i havent stopped and asked questions. it may need alot of work or even a motor. in the edmunds they say the parts are really cheap too.
     
    jonnyv713, Apr 1, 2008
    #65
  6. cccullen

    cccullen Full Member

    that's sounds pretty cheap, i think i read they go for about $1,600 or so.

    5 1/4 speakers aren't that bad. After i made some adjustments to my amp, and put sound deadening in the doors, my DLS were giving out some pretty good mid bass. I was totally happy with it.

    I don't have the amp up to it anymore and i took out my sub already, I'm just waiting for my new stuff to get in... I hope it will be in soon....
     
    cccullen, Apr 1, 2008
    #66
  7. pedro quiroga

    pedro quiroga Well-Known Member

    is it the coupe or the sedan? i really like the coupe.
     
    pedro quiroga, Apr 2, 2008
    #67
  8. jonnyv713

    jonnyv713 The Young Gun of CAT

    ya its a red coupe. it has a liitle bit of damage to the passenger side from what i seen from the road, my dad said he was gonna look at it tomorrow.
     
    jonnyv713, Apr 2, 2008
    #68
  9. jonnyv713

    jonnyv713 The Young Gun of CAT

    and i think after and if i get that car the first thing i will buy is that L7 so i get it for 170 before it sells out
     
    jonnyv713, Apr 2, 2008
    #69
  10. jonnyv713

    jonnyv713 The Young Gun of CAT

    delete post...
     
    jonnyv713, Apr 2, 2008
    #70
  11. jonnyv713

    jonnyv713 The Young Gun of CAT

    should i get that sub in D2 or D4, the D2 is cheaper and the Crunch amp is 1 ohm stable but idk if that would be too much power for the sub, what do u guys think?
     
    jonnyv713, Apr 2, 2008
    #71
  12. cccullen

    cccullen Full Member

    what's the rms of your crunch amp again?
     
    cccullen, Apr 2, 2008
    #72
  13. jonnyv713

    jonnyv713 The Young Gun of CAT

    Amplifier Class D
    Number of Channels 1 - Mono
    RMS Power (4 ohms) 625 watts x 1 channel
    RMS Power (2 ohms) 1250 watts x 1 channel
    RMS Power (1 ohm) Not Specified
    Bridged RMS Power Not Bridgeable
    Peak Power Output 2500 watts x 1 channel
    Minimum Impedance Unbridged 1 ohm
    Minimum Impedance Bridged Not Bridgeable ohms
    THD at Rated RMS Power .10%
    Speaker Level Inputs No
    Preamp Outputs Yes - 1 pair
    Built-in Crossover Low-pass (LP)
    High-Pass Crossover Frequency N/A
    Low-Pass Crossover Frequency 35 - 250 Hz
    Subsonic Filter 15 - 35 Hz
    Signal-to-Noise Ratio 95 dB
    Channel Separation N/A
    Bass Boost 0 - 10 dB
    Bass/Gain Remote Yes
    Fan Cooled No
    Fuse Rating 50A x 2

    it doesnt say what it is at 1 Ohm but its already at 1250RMS for 2 Ohms
     
    jonnyv713, Apr 2, 2008
    #73
  14. cccullen

    cccullen Full Member

    that amp is overrated, it will probably (not exactly sure) put out about 850-875watts at 2ohms. the amp says it will put out 2500watts max at 1ohm. cut that prolly in half and then some, so you may just want to wire it at 1ohm. you can always put the gain way down so you shouldn't have to worry about putting too much power to your L7 15". The L7 gets 1000 rms and L7's can take a beating.

    So if your getting 1 15" L7 then get the D2 and wire it to 1ohm...
     
    Last edited: Apr 2, 2008
    cccullen, Apr 2, 2008
    #74
  15. jonnyv713

    jonnyv713 The Young Gun of CAT

    so do i really want that amp? or should i look at a better one and have some headroom. but then again pedro has what, isnt it like 500RMS to his and he says his pounds so, idk what do u think i shoudl do? and what sould i run for wires to the amp? like 0/1 or 4 AWG?
     
    jonnyv713, Apr 2, 2008
    #75
  16. jonnyv713

    jonnyv713 The Young Gun of CAT

    jonnyv713, Apr 2, 2008
    #76
  17. jayz85

    jayz85 Full Member

    I dont know about overrated... crunch is also made by maxxsonics like hifonics is... some guys rave about how much power the Crunch 3000d amps put out.
     
    jayz85, Apr 2, 2008
    #77
  18. cccullen

    cccullen Full Member

    I have the 1206D with a 15" L5, i plan to run it a 2ohms (900watts) but i couldn't tell you how it performs cuz i actually don't have it yet. So, i'll just tell you from what I know about the 1606D. I know someone that has on hooked up to 2 12" L7 and he says it hits hard. fstrfvo has a hifonics amp hooked up to 1 12" L7 and said it pounds hard.

    Other people say they don't like Hifonics and others do. Very mixed reviews, but it is better than the crunch amp (even though it's made by the same company MAXXSONICS).

    I would ask other members about running a 15" L7 at 1ohm with the BXI1606D. Hifonics is also overrated but i don't know by how much so I wouldn't want you killing your new L7 by putting too much power to it. If you put your gain down, i'm pretty sure you'll be ok though.
     
    cccullen, Apr 2, 2008
    #78
  19. pedro quiroga

    pedro quiroga Well-Known Member

    Last edited: Apr 3, 2008
    pedro quiroga, Apr 3, 2008
    #79
  20. electrolytic

    electrolytic Full Member

    1000 watts will fry that sub, i stick around 650-750 watts.
     
    electrolytic, Apr 3, 2008
    #80
Page 4 of 8